77d7eb28

10:24. Replacement of the bearing of a back wheel (model with DOHC engines)

Prevention

As replacement of the bearing rather difficult operation, before its performance read all section. For performance of this operation it is necessary to use a dynamometer key and a special stripper, and also a new nut of fastening of a nave.

Removal

Arrangement of a plastic cover on a gear rotor of the ABS sensor

Arrangement of a nut of fastening of a nave of a back wheel on models with DOHC engines

Removal of a lock ring of the hug bearing on models with DOHC engines

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports. Remove back wheels.
2. Remove a bracket of fastening and take a brake tube from an arm on number diagonal the lever. Keep in mind that on a bracket the ABS sensor wire is also fixed.
3. Unscrew bolts and remove a support of a brake and an arm of the ABS sensor from a brake board. Using a soft wire, tie up a support with an ABS sensor arm to the car bottom.
4. Unscrew the screw and remove a brake disk. If the brake disk is not removed, take away from it blocks of the emergency brake, rotating the regulator the screw-driver inserted through an opening in a brake disk.
5. Using the face key inserted through an opening in a nave flange, unscrew four bolts fixing a brake board. Keep in mind that the top bolts are shorter than lower.
6. Using a screw-driver edge as the lever, remove a plastic cover from a back part of a gear rotor of the ABS sensor for access to a nut of fastening of a nave (see rice. An arrangement of a plastic cover on a gear rotor of the ABS sensor, the Arrangement of a nut of fastening of a nave of a back wheel on models with DOHC engines).
7. Using a screw-driver edge as the lever, unbend the blocking rim of a nut of a nave and remove it from a gear rotor of the ABS sensor.
8. When unscrewing a nut of fastening of a nave for deduction of a nave from a provorachivaniye screw in two bolts of fastening of a wheel in a flange of a nave and insert between them mount. Unscrew a nut of fastening of a nave.
9. Using a stripper, remove a gear rotor of the ABS sensor from a nave.
10. Using the stripper installed on the diagonal lever remove a nave of a back wheel from the bearing. Keep in mind that the internal ring of the bearing can remain on a nave.
11. Remove a lock ring of the bearing from the outer side of the diagonal lever (see rice. Removal of a lock ring of the hug bearing on models with DOHC engines). Beat out a copper drift an external ring of the bearing from a nave, at the same time a drift of an ustanavla howl evenly around in order to avoid a bearing distortion.
Prevention

At knocking-out of the bearing be careful that there were no zaboina on a bearing seat in a nave.
12. If the internal ring of the bearing remained on a nave, remove it with application of a stripper.

Installation

PERFORMANCE ORDER
1. Clear all details and check their state.
2. Using a tubular mandrel of the corresponding diameter, pressing an external ring of the bearing, install the new bearing in the diagonal lever. Install the bearing against the stop it in a fillet.
3. Establish a lock ring of the bearing and check that it accurately зафиксиро vatsya in a flute.
4. While the assistant supports an internal ring of the bearing, from a reverse side of the diagonal lever with use of a metal tubular mandrel from outer side of the diagonal lever insert a nave into place. Do not make sharp and great efforts as it is easy to damage the bearing.
5. Establish a gear rotor of the ABS sensor on a nave. At the same time from the outer side support a nave.
6. Screw a new nut of fastening of a nave and tighten it the required moment. At the same time hold a nave from a provorachivaniye also, as well as at removal.
7. Establish the new blocking rim on a nave nut and unbend it to a gear rotor of the ABS sensor.
8. Establish a plastic cover on a back part of a gear rotor of the ABS sensor.
9. Screw in bolts of fastening of a brake board and fix them by the required moment.
10. Establish a brake disk and fix it by the screw, then several times tighten the emergency brake in order that the mechanism of the regulator moved blocks into position.
11. Establish a support and an arm of the ABS sensor on a brake board and tighten fastening bolts the required moment.
12. Establish a brake tube in an arm on the diagonal lever and fix it by a bracket.
13. Establish a wheel, then lower the car on the earth and tighten bolts of fastening of a wheel the required moment.