77d7eb28

3.1.13. Installation


Installation of a persistent washer on a bent shaft

 

Installation of a segment spline on a bent shaft
 

Installation of a pulley of a gear belt on a bent shaft
 

Installation of a washer and bolt of fastening of a pulley of a bent shaft
 

Tightening of a bolt of fastening of a pulley of a bent shaft the required moment
 

Tightening of a bolt of fastening of a pulley of a bent shaft its dovorachivaniye on the required corner
 

Installation of a pulley of a bent shaft, a nave outside, on the engine of 1,6 l
 

Installation of a pulley of the camshaft
 

Tightening of a bolt of fastening of a pulley of the camshaft on the engine of 2,0 l
 

Installation of laying of a cover of a head of the block of cylinders
 

Tightening of bolts of fastening of a cover of a head of the block of cylinders
 

Installation of a gear belt on the engine of 2,0 l
 

Installation of a pulley of a bent shaft on the engine of 1,6 l

 

Screwing up of bolts of fastening of a pulley of a bent shaft on the engine of 2,0 l
 

PERFORMANCE ORDER
1. Establish back casings of a gear belt in the sequence, the return to removal. Check that the main cover was correctly combined with a cover on the water pump.
2. On C16 NZ2 engines 1,8 and 2,0 of l establish a persistent washer (see rice. Installation of a persistent washer on a bent shaft) and a segment spline on an end face of a bent shaft (see rice. Installation of a segment spline on a bent shaft). Establish a pulley of a bent shaft (see rice. Installation of a pulley of a gear belt on a bent shaft) also fix it by a bolt with a washer, having tightened a bolt the required moment in two stages. For keeping of a bent shaft from a provorachivaniye when tightening a bolt the assistant has to include any transfer and press a brake (see rice. Installation of a washer and bolt of fastening of a pulley of a bent shaft, Tightening of a bolt of fastening of a pulley of a bent shaft the required moment, Tightening of a bolt of fastening of a pulley of a bent shaft its dovorachivaniye on the required corner).
3. On l engines 1,4 and 1,6 except a dvigata leu of C16 NZ2 establish a segment spline and a pulley of a bent shaft on a bent shaft (see rice. Installation of a pulley of a bent shaft on the engine of 1,6 l).
4. Establish a camshaft pulley, at the same time an adjusting pin on distributive to a shaft has to enter an opening of a pulley and fix a pulley by a bolt, having tightened it the required moment (see rice. Installation of a pulley of the camshaft, Tightening of a bolt of fastening of a pulley of the camshaft on the engine of 2,0 l). When tightening a bolt of fastening of a pulley hold the camshaft from a provorachivaniye a wrench for vents between cams of the third and fourth cylinders. Check a condition of laying of a cover of a head of the block of cylinders and, if necessary, replace it. Establish laying and a cover of a head of the block of cylinders (see rice. Installation of laying of a cover of a head of the block of cylinders). Establish arms of fastening of high-voltage wires under bolts of fastening of a cover of a head of the block of cylinders and screw a cover bolts (see rice. Tightening of bolts of fastening of a cover of a head of the block of cylinders). Connect a hose of ventilation of a case to a cover of a head of the block of cylinders.
5. Temporarily establish a pulley of a vspomog of a telny driving belt on a bent shaft and check that adjusting tags on a pulley of a bent shaft and a pulley of the camshaft are combined with indexes. Remove a pulley vspomogatelno about a driving belt from a bent shaft, then put on a gear belt on pulleys, since a pulley of a bent shaft (see rice. Installation of a gear belt on the engine of 2,0 l).
6. Establish a pulley of an auxiliary driving belt on a bent shaft and fix by bolts, having tightened them the required moment. For keeping of a bent shaft of the engine from a provorachivaniye when tightening bolts of fastening of a pulley of a bent shaft the assistant has to include any transfer and press a brake (see rice. Installation of a pulley of a bent shaft on the engine of 1,6 l, Screwing up of bolts of fastening of a pulley of a bent shaft on the engine of 2,0 l).
7. Adjust a tension of a gear belt.
8. On models with the engine of 1,6 l with the amplifier of steering install the pump of the amplifier of steering.
9. Establish an external casing of a gear belt, and on C16 NZ2 engines 1,8 and 2,0 of l connect the electric socket to the sensor of the index of temperature.
10. Establish a driving belt of the generator and adjust its tension.
11. On l C16 NZ2 engines 1,8 and 2,0 with the amplifier of steering establish a driving belt of the pump of the amplifier of steering and adjust its tension.
12. Connect a weight wire to the accumulator.